In mechanised pipeline welding with an orbital carriage, you weld the root and hot pass by hand. The carriage travels on a band around the pipe and lays the fill and cap passes. Böhler pipeRunner is that kind of carriage, also called a welding bug. It weighs 14 kg, welds pipe from 8 in upwards with flux-cored wire and stores up to 11 passes in one program. This guide takes you from choosing the kit, through joint preparation and parameters, to procedure qualification and purchase cost.
Our figures come from two sources. The first is data from voestalpine Böhler Welding. The second is the first pipeRunner trial in Poland, which we ran with a customer and the manufacturer. The pipe was 24 in (Ø610 mm) with a 17.5 mm wall, in L485ME steel. Where the manufacturer does not publish a figure, we say so in the text.
You can also watch the whole trial on our YouTube channel. The narrated video runs for 10 minutes 20 seconds.
Böhler pipeRunner in 6 numbers
| Parameter | Value |
|---|---|
| Carriage weight without spool | 14 kg |
| Smallest pipe diameter | 8 in (219.1 mm) |
| Travel speed | 0 to 1.6 m/min |
| Torch oscillation width | 0 to 60 mm |
| Passes in one program | up to 11 |
| Manufacturer's trial on 36 in x 15 mm pipe | 66 minutes per joint instead of 109 |
Who this guide is for
- You run a site or a fabrication shop and want to know whether mechanising the fill passes will cut joint time.
- You are a welding engineer or welding coordinator and you are preparing a WPS for flux-cored wire on a carriage.
- You are an operator and want to see, step by step, what working with the carriage looks like.
You will find the price, kit contents and enquiry form on our orbital MIG/MAG pipe welding: Böhler pipeRunner page. See also the product page with price and lead time. Here we focus on how to weld with the system.
How the pipeRunner carriage and the hybrid method work
Böhler pipeRunner is a mechanised MIG/MAG carriage. It travels on a band fitted to the pipe next to the joint and guides the torch along the groove. The manufacturer designed it for uphill welding with flux-cored wire, that is, for the fill and cap passes. In the US this set-up is called bug-and-band welding, and the processes are SMAW (111), GTAW (141) and FCAW (136).
The 4 parts of the system
- Guide band. A band of austenitic spring steel, made for one nominal pipe diameter. Spring-loaded stand-offs and a locking lever hold it on the pipe and compensate for ovality.
- Carriage. An aluminium frame with 4 handles, brushless DC drives and a 5 kg spool on board. The torch has 65 mm of horizontal travel and 30 mm of vertical travel. It tilts by ±25° and oscillates up to 60 mm.
- Power source. TERRA 400 PRM with the RC 100 MP remote control, 340 A at 100% duty cycle.
- Program. Up to 11 passes, each with its own settings. You build the program in a PC application and adjust the settings from the remote control while welding.
Who welds which pass in the hybrid method
| Pass | Process | Who welds | Direction |
|---|---|---|---|
| Root pass | cellulosic electrode (111) or TIG (141) | welder | downhill with a cellulosic electrode |
| Hot pass | cellulosic electrode (111); for stainless steels and clad pipe as per the WPS | welder | downhill with a cellulosic electrode |
| Fill passes | gas-shielded flux-cored wire (136) | operator with pipeRunner | uphill, from 6 o'clock to 12 o'clock |
| Cap pass | gas-shielded flux-cored wire (136) | operator with pipeRunner | uphill, with wider oscillation |
You weld each half of the pipe separately. The carriage starts at the bottom, at 6 o'clock, and finishes at the top, at 12 o'clock. You weld the second half with the same carriage in the opposite direction, because the drive works both ways.
Why flux-cored wire, welded uphill
Rutile flux-cored wire forms a fast-freezing slag that supports the weld pool in the vertical position. That lets you weld uphill with oscillation and fuse into both sidewalls of the groove. Böhler pairs pipeRunner with seamless diamondspark RC-Pipe wires. Their classification carries the H4 designation, which means up to 4 ml of diffusible hydrogen per 100 g of weld metal. According to the manufacturer, the seamless design does not absorb moisture in storage.
What the pipeRunner kit consists of
Besides the carriage you need a band for your diameter, a power source, cables, wire and gas. The table shows an example kit with Böhler Welding part numbers.
| Item | Part number | What it does | What to watch out for |
|---|---|---|---|
| pipeRunner carriage | 73.51.001 | travel on the band, oscillation and wire feed | 14 kg without spool, frame with 4 handles |
| Carriage remote control | 73.52.101 | controls the carriage at the joint | the operator holds it at all times |
| Carriage power supply, 230 V | 73.52.102 | powers the drives and the controls | needs a 230 V supply |
| ABIMIG MT 305 machine torch, 0.75 m | as per quote | delivers wire and gas to the groove | the contact tip and gas nozzle are the parts you replace most often |
| Guide band | 73.51.009 (14 in), 73.51.007 (24 in) | track for the carriage | one band per nominal diameter |
| TERRA 400 PRM power source | 55.13.011 | welding current from 3 to 400 A | 3 x 400 V supply, 30 A fuse, can run from a generator |
| RC 100 MP remote control for the power source | 71.02.209 | voltage adjustment at the joint | designed for work on pipeline sites |
| CAN bus cable, 25 m | as per quote | communication between carriage and power source | protect the connectors from mud and crushing |
| Cable package 2 x 70 mm², 20 m | as per quote | welding current | the 20 m length limits how far the power source can be from the joint |
| diamondspark RC-Pipe flux-cored wire, 1.2 mm | by steel grade | fill and cap passes | the 5 kg spool rides on the carriage |
| M21 shielding gas | not applicable | arc shielding | 15 to 25 l/min, a tent is needed on site |
| FOX CEL and FOX CEL 80-P cellulosic electrodes | by diameter | root and hot pass | used by the welder, not the carriage |
The manufacturer supplies the carriage in a case for transport and storage. The case has a pressure equalisation valve for air freight.
The price on the product page covers the base configuration. Your quote lists what it includes, and this may differ from the table above. We match the bands to your diameters, and the power source, torch and wire to your material and wall thickness. You will find the current list in the configuration section of the system page.
Böhler pipeRunner technical data
All values come from voestalpine Böhler Welding data.
Carriage
| Parameter | Value |
|---|---|
| Weight without spool | 14 kg |
| Dimensions | 480 x 400 x 260 mm |
| Pipe diameter | from 8 in (219.1 mm); the manufacturer gives no upper limit |
| Travel speed | 0 to 1.6 m/min |
| Oscillation width | 0 to 60 mm |
| Oscillation speed | 0 to 350 cm/min |
| Horizontal torch travel | 65 mm |
| Vertical torch travel | 30 mm |
| Torch tilt | ±25° |
| Wire diameter | 1.0 to 1.6 mm |
| Wire feed speed | up to 19 m/min |
| Current rating | 300 A at 100% duty cycle (CO2) |
| Passes per program | up to 11 |
| Travel direction | clockwise and anticlockwise |
| Drives | brushless DC motors |
| Wire spool | 5 kg |
| Programming | PC application; a ruggedised tablet is an option |
| Name variants you may see | pipeRunner, PipeRunner, pipe runner |
TERRA 400 PRM power source
| Parameter | Value |
|---|---|
| Current range | 3 to 400 A |
| MIG/MAG duty cycle at 40 °C | 400 A at 50%, 360 A at 60%, 340 A at 100% |
| Mains supply | 3 x 400 V ±15% |
| Power | 22 kVA |
| Fuse | 30 A |
| Protection rating | IP23S |
| Weight | 22.5 kg |
| Dimensions | 620 x 240 x 460 mm |
| Generator operation | yes |
Which pipes and materials pipeRunner welds
Diameters and wall thicknesses
The smallest pipe is 8 in, which is 219.1 mm. The manufacturer gives no upper limit. You order the band for a specific nominal diameter, so 3 diameters on site mean 3 bands. Inches give the nominal pipe size and millimetres the outside diameter.
Trials with known results:
| Pipe | Material | Who ran the trial |
|---|---|---|
| 36 in (914 mm) x 15 mm | X70 | Böhler Welding |
| 24 in (610 mm) x 25 mm | X60 | Böhler Welding |
| below 20 in, wall 20 to 25 mm | X65 clad with alloy 625 | Böhler Welding |
| dimensions not given in the source | austenitic steel 304L | Böhler Welding |
| Ø610 x 17.5 mm | L485ME | Spawlab with a customer and the manufacturer, first trial in Poland |
The published trials cover wall thicknesses from 15 to 25 mm. We found no published manufacturer results for thicker walls, hydrogen pipelines or offshore work. If your project falls outside this range, start with a procedure trial.
Steel grades
| Pipe material | Wire for fill and cap passes |
|---|---|
| X60 (L415) | diamondspark X60 RC-Pipe |
| X70 (L485) | diamondspark X70 RC-Pipe |
| X70 for sour service | diamondspark X70 RC-Pipe (N) |
| X80 (L555) | diamondspark X80 RC-Pipe |
| Pipe clad with alloy 625 | FOXcore 625-T1 |
| Stainless steel 304L | FOXcore 308L-T1 |
You will find the wire classifications and the root electrodes further down, in the chapter on parameters. If your grade is not in the table, write to us. We will discuss wire selection during the application review.
What pipeRunner does not do
- It does not weld pipe below 8 in.
- In the standard procedure it does not lay the root pass. The manufacturer allows downhill MAG (GMAW) welding, for example for the root, but has not published parameters for it.
- The manufacturer lists no automatic seam tracking function, so assume that the operator keeps the torch on the groove centre line.
Welding step by step, from bevel to cap
The sequence is the same as in our video from the first trial in Poland. Only the step numbers differ. Steps 1, 2, 3, 5, 6 and 7 each link to the relevant point in the video.
Step 1. Prepare the joint and weld the root
In our trial the joint had a 60° V groove, and a welder had laid the root beforehand by TIG. On your job, take the groove shape and the root process from the WPS. The welder lays the root and hot pass by hand, as in your current procedure. After the hot pass, remove the slag and level the profile with a grinder. The first pass from the carriage then has an even base around the whole circumference. Video from 1:45: the 24 in (Ø610 mm) pipe, 60° V bevel and the hybrid method.
Step 2. Fit the band
- Clean mud and spatter off the pipe surface where the band will sit.
- Fit the band next to the joint. Measure its distance from the groove centre line at 4 points: 12, 3, 6 and 9 o'clock. The distance must be the same all the way round. Take the value from the manual for your kit.
- Set the band lock at the top of the pipe, near 12 o'clock, unless the kit manual says otherwise.
- Close the lever and check by hand that the band does not move on the pipe.
If the band sits out of square, the torch drifts off the groove centre line. The operator then has to correct it for the whole pass. Video from 2:47: fitting the band.
Step 3. Mount the carriage and set the torch
- Mount the carriage on the band and lock it as the kit manual describes.
- Set the torch on the groove centre line, at about 90° to the pipe surface.
- Set a wire stick-out of 15 to 20 mm.
- Fit U-groove feed rolls, because you are welding with flux-cored wire. Set the roll pressure so that the wire does not slip but is not crushed.
- Set a gas flow of 15 to 25 l/min.
- Route the cables with slack so that they do not pull on the carriage.
Video from 3:31: setting up the carriage, torch and remote control. For set-up details, see pipeRunner: fitting the guide band and setting up the carriage.
Step 4. Check the program and do a dry run
You build the program beforehand in the PC application. Each pass has its own travel speed, oscillation width and oscillation speed. Before you strike the arc, run the carriage over one full half of the pipe without welding. Watch 2 things: whether the torch stays on the groove centre line and whether the cables pull tight anywhere.
Step 5. Weld the fill passes uphill
You start at 6 o'clock and travel to 12 o'clock. In our trial the first pass from the carriage started at 210 A and 22 V. You walk with the carriage, watch the weld pool and adjust the settings with the remote control if needed. The kit manual gives the adjustment range. At 12 o'clock you end the pass, bring the carriage back down and weld the second half in the opposite direction. Offset the start of each pass from the previous one, so that the starts do not sit on top of each other. On the Ø610 mm pipe one fill pass took about 9 minutes. Video from 4:42: start at 210 A and 22 V and from 5:58: fill, about 9 minutes per pass.
Step 6. Remove the slag and inspect the pass
In our trial there was no grinding between passes. Running a hammer lightly along the pass was enough to remove the slag. After each pass, inspect both groove edges and the start and stop points at 6 and 12 o'clock. Grind out an uneven start or a crater before the next pass. Keep to the interpass temperature in your WPS. Video from 5:29: slag removal without grinding.
Step 7. Weld the cap
You weld the cap with the same wire and wider oscillation, so that the pass covers both groove edges. In the manufacturer's trial on 36 in x 15 mm pipe the whole joint had 7 passes. These were the root, the hot pass, and the fill and cap passes from the carriage. Video from 6:45: cap pass.
Step 8. Remove the carriage and move the band
Unlock the carriage as the manual describes, take it off, open the band lever and move the kit to the next joint. The finished joint goes through visual inspection and non-destructive testing to the extent your project requires.
We describe the whole trial in Böhler pipeRunner trial: welding a 610 mm (24 in) pipe.
Parameters, wires and gases for pipeRunner
Parameters from trials
| Application | Current | Voltage | Travel speed or pass time | Preheat and interpass temperature | Source |
|---|---|---|---|---|---|
| L485ME steel, Ø610 x 17.5 mm pipe, diamondspark X70 RC-Pipe wire 1.2 mm, M21 gas | 210 A at the start | 22 V | about 9 minutes per pass | as per the WPS | Spawlab trial |
| X65 pipe clad with alloy 625 | 150 to 180 A | 23 to 26 V | 18 to 24 cm/min | 80 °C and 150 °C | Böhler Welding |
| Stainless steel 304L | 150 to 180 A | 18 to 22 V | 20 to 24 cm/min | 50 °C and 150 °C | Böhler Welding |
Common settings from the manufacturer's data:
- gas flow 15 to 25 l/min,
- wire stick-out 15 to 20 mm,
- arc length 3 to 5 mm,
- torch at about 90°,
- U-groove feed rolls.
These are starting values from specific trials. Your parameters come from a WPS qualified on your material and your wall thickness.
Wires and electrodes
| Pipe material | Root pass | Hot pass | Fill and cap passes | AWS wire classification |
|---|---|---|---|---|
| X60 (L415) | FOX CEL (E6010) | FOX CEL 80-P (E8010-P1) | diamondspark X60 RC-Pipe, 1.2 mm | E81T1-Ni1M-JH4 |
| X70 (L485) | FOX CEL (E6010) | FOX CEL 80-P (E8010-P1) | diamondspark X70 RC-Pipe, 1.2 mm | E91T1-K2M-JH4 |
| X70 for sour service | as per the WPS | as per the WPS | diamondspark X70 RC-Pipe (N), 1.2 mm | E91T1-GM-JH4 |
| X80 (L555) | as per the WPS | as per the WPS | diamondspark X80 RC-Pipe, 1.2 mm | E101T1-K2M-JH4 |
| X65 clad with alloy 625 | TIG, UTP A 6222Mo-3 rod, 2.4 mm | as per the WPS | FOXcore 625-T1 | see the wire data sheet |
| Stainless steel 304L | TIG, Thermanit JE-308 L rod | as per the WPS | FOXcore 308L-T1 | see the wire data sheet |
Shielding gas
With diamondspark RC-Pipe wires you use M21 shielding gas, which is argon with 15 to 25% CO2. You weld a TIG root under argon. For FOXcore wires, take the gas from the wire data sheet.
Impact toughness in the manufacturer's trials
In the Böhler Welding trials, the average impact energy was 46 to 85 J at -30 °C. At -60 °C it was 33 to 50 J. These figures apply to the pipes and wires in those trials.
Ask about Böhler wires, rods and electrodes on our Böhler Welding at Spawlab page.
How much time pipeRunner saves
Manufacturer's trial: 66 minutes instead of 109
Böhler Welding compared 2 procedures on the same pipe: X70, 36 in (914 mm) x 15 mm.
| Measurement | Cellulosic electrode for the whole joint | Root by hand, the rest with pipeRunner | Difference |
|---|---|---|---|
| Total joint time | 109 min | 66 min | 43 min, about 39% less |
| Arc time | 71 min 42 s | 48 min 25 s | about 32% less |
| Filler metal used | 3.7 kg | 2.02 kg | about 45% less |
| Number of passes | 10 | 7 | 3 fewer |
In the manufacturer's materials you will see a claim of 66% time savings. Its own measurements give 66 minutes instead of 109, which is about 39% shorter. Use 66 and 109 minutes in your calculations. The result comes from one trial on one pipe.
Time for one pass by diameter
The arc time for one pass is the pipe circumference divided by the travel speed. The table uses the full circumference, that is, both halves, for speeds of 18 to 24 cm/min.
| Pipe diameter | Circumference | Time for one pass |
|---|---|---|
| 8 in (219.1 mm) | 688 mm | 2.9 to 3.8 min |
| 12 in (323.9 mm) | 1,018 mm | 4.2 to 5.7 min |
| 16 in (406.4 mm) | 1,277 mm | 5.3 to 7.1 min |
| 20 in (508 mm) | 1,596 mm | 6.6 to 8.9 min |
| 24 in (610 mm) | 1,916 mm | 8.0 to 10.6 min |
| 36 in (914 mm) | 2,871 mm | 12.0 to 16.0 min |
| 48 in (1,219 mm) | 3,830 mm | 16.0 to 21.3 min |
The manufacturer gave the range of 18 to 24 cm/min for pipe clad with alloy 625. In our trial on L485ME steel, one fill pass on the Ø610 mm pipe took about 9 minutes.
What else goes into the calculation
- moving the band and carriage between joints,
- changing the 5 kg spool,
- slag removal and inspection after each pass,
- waiting for the interpass temperature.
You can work out your own case in the joint calculator on the system page. If you prefer figures from your own pipe, book a trial.
When pipeRunner pays off and when to choose another method
The table shows which jobs suit the pipeRunner carriage and where another method is the better choice.
| Your situation | Verdict | Why |
|---|---|---|
| Field joints and tie-ins on pipelines from 8 in | suitable | the carriage weighs 14 kg and runs on a band fitted to the outside of the pipe |
| Pipe-to-elbow joints | suitable | you can mount the carriage on either side of the band, so you fit the band on the straight pipe section |
| Process pipework and prefabrication from 8 in | suitable | repeat diameters, the same program on successive joints |
| Your crew welds the whole joint with cellulosic electrodes today | suitable | root and hot pass stay as they are; you mechanise the fill and cap passes |
| Clad and stainless pipe from 8 in | suitable after a trial | the manufacturer has parameters for alloy 625 and 304L steel |
| Long, large-diameter transmission pipeline built by a mainline spread | choose another system | systems with an internal line-up clamp and several heads welding downhill give more joints per shift |
| Pipe below 8 in | not suitable | this is below the minimum diameter for the carriage |
| Working in wind without a tent | not suitable | wind blows the shielding gas away, and AWS D1.1 allows wind up to 8 km/h for gas-shielded processes |
| A few joints a year | check the costs carefully | the cost of the kit and of procedure qualification is spread over a small number of joints |
| Hydrogen pipelines, offshore work, wall above 25 mm | start with a trial | we found no published manufacturer results for these applications |
How to prepare the site for the carriage
- Leave enough clear pipe on one side of the joint to fit the band.
- Give the operator access all round the pipe, including underneath, because the pass starts at 6 o'clock.
- Put up a tent or windbreaks.
- Provide a 3 x 400 V supply for the power source and 230 V for the carriage power supply, or bring a generator.
- Place the power source within cable reach, that is, up to 20 m from the joint.
In the video we explain when not to buy pipeRunner (from 8:04) and how to prepare the site for the carriage (from 9:01).
Common mistakes when welding with an orbital carriage
These mistakes are typical of uphill flux-cored welding with a carriage that runs on a band. The table gives the effect of each mistake and how to avoid it.
| Mistake | Effect | How to avoid it |
|---|---|---|
| Band fitted out of square to the joint | the torch drifts off the groove centre line, lack of sidewall fusion on one side | measure the distance from the band to the groove centre line at 4 points |
| Uneven hot pass and slag left by the electrode | lack of fusion and slag inclusions in the first pass from the carriage | grind the hot pass to an even profile |
| Wire stick-out too long | unstable arc, porosity | keep it at 15 to 20 mm and correct the torch height |
| Oscillation too narrow | lack of sidewall fusion | match the width to the groove on every pass, because a V groove widens towards the cap |
| Wind, or a draught through the pipe | porosity | tent, windbreaks and capped pipe ends |
| V-groove rolls and high pressure | crushed flux-cored wire, uneven feeding | U-groove rolls and only enough pressure to stop the wire slipping |
| Cables pulling on the carriage | uneven travel speed, varying pass thickness | a dry run before each half |
| Pass starts and stops always in the same place | imperfections at 6 and 12 o'clock | grind the start and the crater, offset the start of the next pass |
| Interpass temperature too high | lower impact toughness | measure the temperature before each pass and keep to the WPS limit |
| Parameters from someone else's trial instead of your own WPS | a joint not covered by the qualification | treat the figures in this guide as a starting point for a trial |
The operator watches the weld pool and corrects the torch throughout the pass. To run the carriage, choose someone who knows manual flux-cored welding.
Standards for qualifying procedures and operators
When you switch from electrodes to flux-cored wire on a carriage, you change the welding process and the degree of mechanisation. Your current WPS does not cover this. You need a new procedure qualification and a qualification for the operator.
| What you qualify | Standard | What it means in practice |
|---|---|---|
| Welding procedure | EN ISO 15614-1 | pWPS, test piece, testing, the WPQR and, on that basis, the WPS. A joint with the root in process 111 and the fill in process 136 is qualified as a multi-process procedure |
| Gas pipeline welding | EN 12732 | requirements for welding steel pipework in gas infrastructure |
| Pipeline to the client's specification | API 1104 or ISO 13847 | you apply it when the project requires it |
| Carriage operator | EN ISO 14732 | qualification test for welding operators in mechanised welding |
| Welder for the root and hot pass | EN ISO 9606-1 | the same qualification as before |
Order of work
- Collect the project requirements: acceptance standard, steel grade, diameter, wall thickness and impact test temperature.
- Write the pWPS. Take the starting parameters from the trials described above.
- Weld a test piece on your own pipe. Before that, you can book a trial with us on the same pipe, with the scope agreed before we travel.
- Commission the tests and collect the WPQR.
- Train the operators and register them for the test to EN ISO 14732.
Böhler Welding states that its team of welding engineers, weldTECH Application Services, supports pipeline contractors.
More on standards in our guides:
- ISO 9606-1 welder certificate: designation, range and revalidation
- Welding coordinator under EN ISO 14731
- EN ISO 5817: quality levels B, C and D
Daily operation and maintenance
On site the carriage picks up mud, dust and spatter. Go through the lists below before and after each shift.
Before the shift
- Check that the band is clean, free of spatter and dents, and that the lever closes firmly.
- Inspect the torch. The contact tip must not have a worn bore and the gas nozzle must be free of spatter.
- Clean the U-groove rolls and check that the wire runs through without resistance.
- Measure the gas flow at the nozzle. It should be 15 to 25 l/min.
- Tighten and dry the connectors on the control cable and the welding cable.
- Select the program for your diameter and wall thickness and check it with a dry run.
After the shift
- Blow off the dust and remove spatter from the carriage. The kit manual shows the points to clean.
- Wipe the band and put it away so that it cannot deform.
- Store the carriage in its transport case.
- Protect the wire spool from mud and water.
What wears on the band
The band is designed so that the guides wear slowly. The spacer balls wear first, and they are the cheapest part of the band.
Troubleshooting
If the carriage does not respond, check the cables and the power supply as the kit manual describes. If that does not help, call us. Spawlab is an authorised Böhler Welding service centre in Poland. We handle repairs and parts at our workshop in Krotoszyn. Report a fault through the service form.
pipeRunner videos from our YouTube channel
We recorded all 4 videos during the first pipeRunner trial in Poland. You will find them on the Spawlab YouTube channel.
| Video | Length | What you will see |
|---|---|---|
| Automated Pipe Welding | Böhler pipeRunner on a 610 mm Steel Pipe | 10 min 20 s | narrated video in English: joint preparation, fitting the band, setting up the carriage, fill passes and cap |
| Trial video without narration | 2 min 3 s | 4K video without narration: joint preparation, root, fill passes and cap |
| Short: striking the arc | 55 s | arc start, pipe welding and the power source readings |
| Short: the carriage on the move | 1 min | the carriage runs on the band, the torch follows the joint |
The narrated video minute by minute
Click a time in the table to jump to that part of the video.
| Time | What you will see |
|---|---|
| 0:46 | system data and equipment |
| 1:45 | 24 in (Ø610 mm) pipe, 60° V bevel and the hybrid method |
| 2:47 | fitting the band |
| 3:31 | setting up the carriage, torch and remote control |
| 4:42 | start at 210 A and 22 V |
| 5:29 | slag removal without grinding |
| 5:58 | fill, about 9 minutes per pass |
| 6:45 | cap pass |
| 7:19 | manufacturer's trial: 66 minutes instead of 109 |
| 8:04 | when not to buy pipeRunner |
| 8:23 | where pipeRunner makes sense |
| 9:01 | preparing the site for the carriage |
Fitting the band and setting up the carriage
A separate page with a video on preparing the system for use: pipeRunner: fitting the guide band and setting up the carriage.
Spawlab channel on YouTube
We publish more trial videos on our channel. Subscribe and turn on notifications if you want to hear about the next video.
Price, delivery and working with Spawlab
Price and purchase terms
| Item | Value |
|---|---|
| Base configuration price | 53,318.21 EUR net, 65,581.40 EUR gross with 23% Polish VAT. 0% VAT for EU companies with a valid EU VAT number |
| Leasing | available in Poland |
| Delivery | within 30 working days of order |
| Warranty | manufacturer's warranty |
| Service | Spawlab, authorised Böhler Welding service centre in Poland |
Check the current price and availability on the Böhler pipeRunner product page.
How we work together
- Application review. You give us the diameters, wall thicknesses, steel grade and number of joints. We check whether the carriage suits your joints, and we tell you in writing if it does not.
- Configuration. Bands for your diameters, and a power source, torch and wire for your material.
- Quote and preparation for start-up. You receive a quote that lists the kit contents, and we agree the scope of operator training together.
- After-sales support. Service and parts are available from Spawlab in Krotoszyn.
Before the quote you can book a trial on your own pipe. We agree the scope before we travel. We ran the first pipeRunner trial in Poland with a customer and the manufacturer, so we know this carriage from hands-on work.
What to send in your enquiry
- pipe diameters and wall thicknesses,
- steel grade,
- number of joints and the schedule,
- the standard or specification the client uses to accept the joints,
- the procedure you use today,
- place of work: site or workshop.
Contact
- pipeRunner enquiry form
- Book a trial on your own pipe
- Phone: +48 669 162 833, Monday to Friday, 8 am to 4 pm (CET)
- Email: kontakt@spawlab.pl
- Address: Spawlab, ul. Akacjowa 15, 63-700 Krotoszyn, Poland
All pages about this system: pipeRunner system page, product page, customer trials, preparing the system for use and manufacturer's documentation (PDF). You will find other equipment in our welding automation category.
Frequently asked questions about Böhler pipeRunner
Does pipeRunner weld the root pass?
Not in the standard procedure. A welder lays the root with a cellulosic electrode or by TIG. The welder also lays the hot pass, and the carriage welds the fill and cap passes. The manufacturer allows downhill MAG (GMAW) welding, for example for the root, but has not published parameters for it.
What is the minimum pipe diameter for pipeRunner?
The minimum is 8 in, which is 219.1 mm. The manufacturer gives no upper limit. You order the band for a specific nominal diameter.
Does pipeRunner weld pipe-to-elbow joints?
Yes. You can mount the carriage on either side of the band. That lets you fit the band on the straight pipe section next to the elbow.
How long does it take to weld one joint?
In the manufacturer's trial on 36 in x 15 mm pipe the whole joint took 66 minutes. Welded entirely with electrodes, it took 109 minutes. In our trial on Ø610 x 17.5 mm pipe one fill pass took about 9 minutes.
Which wire and gas does pipeRunner use?
For pipeline steels from X60 to X80 you use diamondspark RC-Pipe flux-cored wire, 1.2 mm in diameter, with M21 mixed gas. For pipe clad with alloy 625 you use FOXcore 625-T1 wire, and for 304L steel FOXcore 308L-T1. Choose the gas for FOXcore wires from the wire data sheet.
Do I need to qualify a new welding procedure?
Yes. You change the process and the degree of mechanisation. You need a new procedure qualification to EN ISO 15614-1, or to the standard named in the project, and a new WPS. The root can still be welded with your current process.
What qualification does a pipeRunner operator need?
The carriage operator takes a test to EN ISO 14732. The welder who lays the root and hot pass works under a qualification to EN ISO 9606-1.
Can you weld with pipeRunner in the field?
Yes, under a tent or behind windbreaks, because you weld with shielding gas. The TERRA 400 PRM power source has an IP23S protection rating and can run from a generator.
How much does the carriage weigh and how many people operate it?
The carriage weighs 14 kg without the spool and has 4 handles. An operator works at the joint, and a welder lays the root beforehand.
How does pipeRunner differ from an orbital TIG head?
Closed TIG heads are used for thin-walled, small-diameter tubes. The pipeRunner carriage welds pipe from 8 in by MIG/MAG and runs on a band. The operator controls it with a remote control.
How much does Böhler pipeRunner cost?
The base configuration costs 53,318.21 EUR net, which is 65,581.40 EUR gross with 23% Polish VAT. Leasing is available in Poland. Delivery takes up to 30 working days from order.
Can I see pipeRunner on my own pipe before I buy?
Yes. Book a trial through the form on the trials page or call +48 669 162 833. We agree the scope of the trial before we travel.